Відео

верхний каркас завязать на ось сделать замок в передный части прицепа и нижний не нужен и лебедка тоже не нужна. подьехал открыл замок и гравитация все сделает сама

Thank u taking time

Nice! I want one

Why don't you just buy a dump trailer for all the work of building one?

Great job. I would have turned the tubing on edge instead of flat. Granted you may have a reason that I just do not see. I would add a couple of plates to prevent going over center on the lift. If you happen to pull just that little bit too far, the bed could come crashing down. Or possibly when dumping a heavy load sliding out the back might bounce it enough for the lift arms to go passed center, and same crash. You may be able to put some kind of stop on the cable or winch to prevent pulling too far. I don't know enough about either to suggest how that might be done.

Nice one. I also feel like much heat will be lost during heat transfer.

what is the metal you are using and the springs?

Did that say 245 Trioxin?!?! 😨

that poor little axle...

делал долго ну думаю шота интересное и нужное да выглядит отлично на вид а получилосяяя говно полнейшее столько труда а ума нехватило подогнать до идеала но ниче дороботаеть може и с гавна конфетка получится дерзай но главное старание есть всем мира здоровья удачи

Try doubling the cable with extra pulleys which doubles the pulling power of the winch more pulleys and double it again

I was just thinking of Chopndrop’s comment, the theme song off the road runner cartoon would be fitting. 😂😂😂

Superbe réalisation

That is cool

На деле покажи, мастер

I have questions about the oven being triple sheeted. If the charcoal compartment is seperate from the main body of the oven, why not put the rockwool in the void between the oven body and the larger barrel?

Great video. You are clearly an experienced DYI design engineer and metal fabricator and have the proper tools to do it.

nice job if you want to carry duck-down pillows or ladies lingerie. its a fail. i got it right on my third attempt. i built a tower on the front a frame and installed a winch which lifted the tray which pivoted at the back end. fail. then i installed a plate beneath the deck to fit an air-jacking bag that runs off the exhaust. fail. it didnt lift it far up enough. i moved the plate back a bit. fail. had trouble lifting a full load of sand. the final try worked perfectly. the pivot point was the axle. i copied what the trailer makers in my city, perth western australia, were doing. the man at loadstar trailers claimed the others copied his version. so did i and supersized some components like pivot points and the back of the frame. the back of the frame will be scraping on the ground when i'm tipping. i was also told that the longer the a frame at the front, the more behaved it is when being towed so i added another 150mm there. the trick is to shovel off from the front then the back becomes heavier than the front and tips. then you drive the trailer backwards, the back of it bites into the ground causing the front section to lift up and even go beyond vertical. nothing stays in the trailer then. the rear lights are recessed so they dont get smashed when tipping. i dont carry ladies lingerie. i carry brick rubble, sand and rocks.

done this for years but ruins your hands

важке не підніме. обірветься трос або зламається редуктор

Buen aparato y trabajo

Le plateau est un peu trop haut !

Монтаж видео хороший, суть ясна, без затягиваний, переходы и подача нравится. Изделие получилось жизнеспособным. Может тяжеловато немного, но точно не опрокинется. Автор умничка.

100кг еле поднял.

Trop cool

That welding machine is top notch

😎😎

👨‍🏭👨‍🏭👍👍👍👍👍💪💪💪👌🔥

Очень не грамотная работа😢😢😢 абсолютно бесполезной много

Nice work

Nice work but adding that much weight to a light duty trailer. Ok if you are hauling leaves i guess

Don't do this!!!

This video is not about restoring a lathe. Of painting, cleaning, yes, but not of restoration

Gran trabajo 👏

Just wondering if it's worth my time to build a dump body on a trailer that looks like it gan only hold 500 lbs. My trailer is rated for 3000 lbs and would be far more expensive , the trailer shown is more suited for a four wheeler.

Kannst du nicht reden?

Ficou muiti bm. Mas o ruído alto continua. Vemos q não foi possível reduzí lo.

Hi pechoo.... meanwhile congratularions .... I wanted to know if you used of the particular paint or primer for the calipers and engine block... thanks you

Cum ai legat firele ? Te rog.

omg

ما هو اطوال الحديد

Kako da ocistim karburator?

Good example of a jobless guy doing nonsense.Very healthy to eat food cooked in this garbage you made.

good job

Классная штука чтобы пилить видеоролики с пустым прицепом. С нагрузкой работать не будет. Трос порвется первым. Если его заменить на более толстый - и раму погнет. Геометрию нужно было просчитывать. Удачи в изучении сопромата. )))

Che carbone usi

make me one

I dont like peppers

Прикольно, когда на холостых, а теперь загрузи ту кучу строительного мусора, как в начале, и попробуй также!

Nice ❤